sales@stepmotordriver.com

   >   Stepper Motor Driver

Stepper Motor Driver

  • M860H Stepper Motor Driver,2-phase AC80V,DC110V/7.2A motor driver
M860H Stepper Motor Driver,2-phase AC80V,DC110V/7.2A motor driver

M860H Stepper Motor Driver,2-phase AC80V,DC110V/7.2A motor driver

  • Product description: stepper motor driver,servo driver,driver integrated servo motor,automation products,setpper motor controller,3-axis stepper motor controller
  • INQUIRY

Product Abstract:

The M860H is a excellent performance microstepping based on pure-sine current control.With those technologies and the self-adjustment function(self-adjust current control) to various motors, the stepper driver keep the driven motors run with low noise,less heating, smoother movement and better performances at higher speed than other drives in the markets.it is adapt to driving 2,3,4 phases hybrid stepper motors.


Product Description

The M860H Stepper Motor Drivers is a excellent performance microstepping based on pure-sine current control.With those technologies and the self-adjustment function(self-adjust current control) to various motors, the stepper driver keep the driven motors run with low noise,less heating, smoother movement and better performances at higher speed than other drives in the markets.it is adapt to driving 2,3,4 phases hybrid stepper motors.

M860H Stepper Motor Driver's Features

High Efficiency

Excellent high speed performance

Max AC80V or DC110V

Max output 7.2A

Self-adjustment function

Pure-sine current control

300KHz Max Pulse input frequence

Suitable for TTL and optically isolated input

Auto idle current reduction

16 steps resolutions in decimal binary, max 51,200 steps/rev

Suitable for 2 ,3, 4 phases motors

Support PUL/DIR and CW/CCW modes

Short-voltage protection, over-voltage protection, over-current protection

 

M860H Stepper Motor Driver’s Specifications

M860H Stepper Motor Driver’sElectrical Specifications (Tj : 25oC~77oC)

 

Parameters

M860

Min

Typical

Max

Unit

Output Current

1.80

-

7.2 (5.1 RMS)

A

Input Voltage

+24

+68

+80

VDC

Logic Signal Current

7.00

10

16

Ma

Pulse input frequency

0.00

-

300

KHz

PulseWidth

2.50

-

-

Us

Pulse Voltage

5.00

-

24

VDC

Isolation resistance

500.00



 

 

M860H Stepper Motor Driver’s Connector P1 Configurations

 

Pin Function Details
PUL+(+5V) Pulse signal: In single pulse pulse/direction) mode, this input represents pulse signal, effective for each rising or falling edge (set by inside jumpers in JP1); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,effective for high level or low level (set by inside jumpers in JP1). For reliable response, pulse width should be longer than 1.5μs. Series connect resistors for current-limiting when +12V or +24V used.
PUL-(PUL)
DIR+(+5V) DIR signal: In single-pulse mode, this signal has low/high voltage levels,representing two directions of motor rotation; in double-pulse mode (set by inside jumper J3), this signal is counter-clock (CCW) pulse,effective for high level or low level (set by inside jumper J1). For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH,0-0.5V when DIR-LOW.
DIR-(DIR)
ENA+(+5V) Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary,namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED).
ENA-(ENA)

 

M860H Stepper Motor Driver’sConnector P2 Configurations

 

Pin Function Details
GND DC/AC power ground
+V DC/AC power supply, 20~80V, Including voltage fluctuation and EMF voltage.
A+,A- Motor Phase A
B+,B- Motor Phase B

 

M860H Stepper Motor Driver’s Microstep and Current

The drives uses an 8 bits DIP switch to set stepper motor resolution and motor operating current, as shown below:

Dynamic Current(1/2/3)           Microstep Resolution(6/7/8)

1

2

3

4

5

6

7

8

Standstill Current(4,Half/Full)

M860H Stepper Motor Driver’sMicrostep Resolution Selection

Microstep resolution is set by SW5, SW6, SW7, SW8 of the DIP switch as show in following:

 

Step Angle Pulse/Rev SW5 SW6 SW7 SW8
0.9 400 ON ON ON ON
0.45 800 ON OFF ON ON
0.225 1600 ON ON OFF ON
0.1125 3200 ON OFF OFF ON
0.05625 6400 ON ON ON OFF
0.028125 12800 ON OFF ON OFF
0.014063 25600 ON ON OFF OFF
0.007031 51200 ON OFF OFF OFF
0.36 1000 OFF ON ON ON
0.18 2000 OFF OFF ON ON
0.072 5000 OFF ON OFF ON
0.036 10000 OFF OFF OFF ON
0.0144 25000 OFF ON ON OFF
0.0072 50000 OFF OFF ON OFF

 

M860H Stepper Motor Driver’s Current Settings

The first three bits (SW1, 2, 3) of the DIP switch are used to set the dynamic current. Select a setting closest to your motor’s required current.

 

Peak current (A) RMS(A) SW1 SW2 SW3
2.40 1.71 on on on
3.08 2.20 off on on
3.77 2.69 on off on
4.45 3.18 off off on
5.14 3.67 on on off
5.83 4.16 off on off
6.52 4.66 on off off
7.20 5.14 off off off

 

M860 Stepper Motor Driver’s Typical Connections

close
Scan the qr codeClose
the qr code